Green Solutions. Green Savings.

Site Map
Home
About Us
Residential Maintenance
Commercial Maintenance
Rooftop Unit Maintenance
Blogs
Contact Us
FAQs


































Precision Furnace Tune-up Benefits:

  • Lower utility bills by reducing energy

         

          consumption and waste.

  • Extended equipment life.
  • Peace of mind for you and your family.
  • Fewer repairs and improved system  reliability.
  • Increased heating capacity and efficiency.
  • Priority service scheduling.


Precision Air-Conditioning Tune-up Benefits:


  • Lower utility bills by reducing energy consumption and waste.
  • Extended equipment life.
  • Peace of mind for you and your family.
  • Fewer repairs and improved system reliability.
  • Increased cooling capacity and efficiency.
  • Priority service scheduling.




































Our Exclusive Precision Tune-Up Procedure Includes, As Needed:




































1.     Inspect and tighten all electrical connections and terminals.

2.     Inspect all wiring and wiring insulation to ensure safe operation.

3.     Remove, clean, and adjust main gas burners.

4.     Inspect ignition wiring along with flame safety wiring.

5.     Thoroughly inspect heat-exchanger(s) & combustion chambers for cracks, rusting, or problem areas.

6.     Vacuum out blower compartment; return airdrop, and surrounding area. (No duct cleaning)

7.     Inspect all return and supply air registers throughout the conditioned space.

8.     Inspect flue piping and/or induced draft motor assembly connections.

9.     Test and inspect all furnace safety controls.

10.  Test, record, and adjust gas pressure.

11.  Replace or clean standard air filters.

12.  Inspect blower motor, drive mechanism and fan assembly.

13.  Lubricate all fan motors and all moving parts.

14.  Adjust all dampers and set proper blower speed(s).

15.  Verify proper thermostat operation and programming.

16.  Tighten blower wheel hub set screw.

17.  Inspect, test and document thermocouple/flame sensor output signal.

18.  Measure and record electrical voltage, amperage, and component resistance.

19.  Inspect and test all system transformers, relays, contactors, and controls. Measure performance

20.  Repair minor air leaks in plenum and return airdrop.

21.  Perform a complete and thorough, room-by-room, electronic carbon monoxide check of the entire house.

22.  Advise customer on other ways to reduce energy consumption, improve safety and enhance comfort.



1.     Inspect condenser coil surface area and rinse with water (dependent on water source availability).

2.     Thoroughly clean or replace standard air-filter(s).

3.     Wash and check condensing unit leveling for proper motor and bearing wear.

4.     Lubricate motor and fan bearings as well as other moving parts as necessary.

5.     Inspect evaporator coil and drain pan when readily accessible.

6.     Clean and inspect condensate drain lines and fittings.

7.     Verify proper thermostat operation and programming.

8.     Adjust all dampers and set proper blower speed(s)

9.     Inspect, tighten and test all electrical connections. This includes disconnect switch.

10.  Inspect all cooling system electrical wires, connectors, and terminals.

11.  Test system starting and running capacitors.

12.  Test all controls, switches, relays, transformers, contactors, motors, and fans.

13.  Measure motor amp draw, line voltage, and control voltage.

14.  Test system-starting capabilities.

15.  Test system for proper airflow and air delivery.

16.  Inspect and adjust all safety controls.

17.  Check and record refrigerant pressures and temperatures to ensure proper system charge.

18.  Test and record super-heat and sub-cooling. Compare with factory specifications.

19.  Adjust refrigerant metering control device per factory/manufactures recommendations.

20.  Test and measure air-conditioning system for proper production and capacity.

21.  Monitor fan motors and compressor operating temperatures.

22.  Complete and present full written report.